Plumbing Services in Portland, OR
Cully Plumbing provides a full range of plumbing services for homes and businesses across Portland, Oregon. From routine drain cleaning to water heater replacement and sewer line diagnostics, our team uses professional-grade tools and proven methods to resolve plumbing problems correctly the first time.
Below is a detailed breakdown of the services we offer, the common causes behind each problem, and how our technical approach addresses it properly.
Service Summary
| Service | Typical Use |
|---|---|
| Drain Cleaning & Hydro-Jetting | Clogged or slow drains |
| Water Heater Installation & Repair | No hot water, leaks, replacement |
| Pipe Repair & Repiping | Leaks, low pressure, corroded lines |
| Fixture Installation | Faucets, sinks, toilets, disposals |
| Sewer Line Diagnostics | Backups, root intrusion, camera inspection |
| Leak Detection | Hidden leaks, slab leaks, moisture |
| Bathroom & Kitchen Plumbing | Remodels, rough-in, finish plumbing |
Drain Cleaning & Hydro-Jetting
Method: Mechanical augering combined with high-pressure hydro-jetting clears grease, soap scum, and debris from residential and commercial drain lines throughout the Portland area.
Common Causes: Buildup from grease, hair, soap, food solids, and mineral scale gradually narrows pipe interiors until flow is restricted or fully blocked.
Our Approach: We diagnose the blockage, clear it with the appropriate method, then flush the line to restore full diameter. Hydro-jetting removes residual buildup so drains stay clear longer.
Water Heater Installation & Repair
Method: Installation and replacement of tank and tankless water heaters, including gas, electric, and heat-pump units, plus repair of heating elements, thermostats, and valves.
Common Causes: Sediment accumulation, corroded anode rods, failing heating elements, and pressure-relief valve wear are common reasons water heaters underperform or leak.
Our Approach: We size the unit to the household, remove and dispose of the old tank, install to current plumbing code, and verify temperature, pressure, and discharge piping before finishing.
Pipe Repair & Repiping
Method: Targeted repair of leaking or corroded supply and drain lines, and whole-home repiping using PEX or copper where aging galvanized or cast-iron lines are failing.
Common Causes: Older Portland homes often have galvanized steel or cast-iron piping that corrodes from within, producing low pressure, discolored water, and pinhole leaks.
Our Approach: We identify the failing section, recommend repair versus repipe based on pipe condition, and install approved materials with proper fittings and supports to code.
Fixture Installation
Method: Installation and replacement of faucets, sinks, toilets, garbage disposals, and shut-off valves for kitchens, bathrooms, and laundry areas.
Common Causes: Worn washers and cartridges cause drips; aging fixtures crack or corrode; and remodels or upgrades require new fixtures to be set and connected properly.
Our Approach: We shut off and verify water supply, remove the old fixture, inspect supply lines and stops, and install the new fixture leak-free with correct sealing and support.
Sewer Line Diagnostics
Method: Camera inspection of sewer laterals to locate cracks, root intrusion, bellied sections, and blockages, with diagnostic reporting for repair planning.
Common Causes: Tree roots seeking moisture, shifting soil common in Portland, aging clay or cast-iron laterals, and grease buildup all contribute to sewer line failure.
Our Approach: We run a camera through the line, mark problem locations, and explain findings clearly so you can make an informed decision about repair or replacement scope.
Leak Detection
Method: Pressure testing, acoustic listening, and moisture inspection to pinpoint hidden leaks behind walls, under slabs, or in concealed piping.
Common Causes: Corroded fittings, failed solder joints, slab movement, and worn supply lines create leaks that may not be visible until damage appears.
Our Approach: We isolate the system, test pressure, and narrow down the leak source with minimal disruption to your home before recommending the least invasive repair path.
Bathroom & Kitchen Plumbing
Method: Complete rough-in and finish plumbing for bathroom and kitchen remodels, including supply, drain, vent, and fixture connections.
Common Causes: Remodels relocate fixtures and require new supply and drain routing; older kitchens and baths often need updated valves and lines to meet code.
Our Approach: We coordinate with your remodel schedule, rough in supply and DWV lines to layout, and return for finish work once fixtures are ready to set.
Need a Specific Service?
Tell us what's going on and we'll diagnose it and provide a straightforward quote.